1/9/2024 0 Comments Bgw210 att routerI have since moved when I posted this comment and now live in an area with xgs-pon and was given an all in one bgw-320 rg. Then disconnect once service is restored. If you lose it you’ll need to reconnect AT&T rg and let it authenticate again. That’s it leave it connected and unless you lose power you will keep service. If you do, just disconnect the AT&T rg from the switch. Make sure you have internet on your router. ONT > dumb switch ( I used a 5 port netgear) plug your att router into the switch as well and wait for the lights to turn green ( authenticate ) plug in your router to the switch as well. It’s very simple to bypass.Ĭlone the Mac of the AT&T rg to your router. I have a UDM pro se, but any router that can clone a Mac will suffice.Īs far as guides, I’m not sure. Hoping there is a solution! Thanks for the help. I’d like to avoid plan B where I buy another router if possible. I’m sorry if this is something that has been asked a million times, if so, I’m just not finding the right thread. I’m not certain, but I think my wifi devices are still using my AT&T router for their DHCP leases, because they don’t seem to show up as devices with DHCP leases in PiHole or in the dashboard, and my PC seems to be unable to get a lease for an IP at all. Turn off ipv6 everywhere (AT&T router, my computer, PiHole)įollowing these steps, the Wi-Fi will work on my devices but they don’t seem to be going through PiHole and my PC that is hardwired to the AT&T router stops connecting to the internet.Set the PiHole Gateway to 192.168.1.254 (my AT&T Router?).Assign my PiHole device a static IP on my AT&T router of 192.168.1.111.My research suggests the best solutions are to either let PiHole manage my DHCP (plan A) or buy another router (plan B).įollowing guides, I have tried the following steps: I have AT&T fiber and the router won’t let me change the DNS settings. Hello! I’ve done some searching but I can’t seem to find help on the problem I’m stuck on. This wasn't what I wanted, but looking at some of the features of new routers convinced me it was worth the money. I'll set the AT&T router to pass through to the router I purchased and configure the DNS from there. Thanks everyone for all the help.ĮDIT: I've caved and purchased a wifi6 router. I didn't want to shell out for the new router, but if anyone else with AT&T fiber stumbles upon this thread, I wanted to document what ended up working best for me. If the returned equipment is damaged due to abuse, we may add a damaged equipment fee to your bill.EDIT 2 SOLVED: I've setup my new WiFi 6 router, set the DNS to the PiHole, and all is working as intended.To avoid a fee, return your undamaged equipment within 21 days of the service change or disconnect date.Equipment you own 3 rd party (non AT&T) extenders, HDMI cables, or Ethernet cablesįYI: Don't remove or unplug wall-mounted equipment.Įquipment you own like extenders, HDMI cables, or Ethernet cablesĪntenna and accessories like the mount and pole.Terminals (ONTs) that may be found in closets, garages, attics, or outside your home Wall-mounted equipment like Ethernet jacks, Fiber jacks, or Optical Network.Wi-Fi extenders if they're included as a part of your Extended Wi-Fi Service.While each return process may be different, we have a general list of what you should send back and what you can keep. Check your email for what you’re required to send back and next steps.įYI: If you’re expecting an email but don’t see it, check your spam or junk folders. Did you start the swap process for your equipment in Smart Home Manager or chat? Have you already spoken to an agent about your return? Based on your service and equipment, what you have to return may vary.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |